Precision Mro Solutions

SIZE: 4" X 12'''' LONG

Introduction:

Wrap Seal® ULTRA Quick Repair Kit for Active Pipe Leaksis a leak repair system that no shutdown required. It is applicable on any metal or non-metal pipes and used in

many industries such as oil and gas, petrochemical, offshore, marine, etc.

Features:

· Repairs under active leak up to 150 psi (11 kg/cm²) pressure

· Applicable to pipes up to 18” (457 mm) diameter

· Withstand pressure up to 500 psi (35 kg/cm²)

· Withstand temperature up to 200 °C (392 °F)

· Safe for drinking water and resistant to most chemicals

· Ideal for pipeline reinforcement

Typical Properties:

Operating temperature                -50 °C to 200 °C (-58 °F to 392 °F)

Tensile strength                          3,920 psi (276 kg/cm²)

Bond strength                             230 psi (16 kg/cm²)

Compression strength                 13,750 ± 530 psi (967 ± 37 kg/cm²)

Yield strength                              2,260 psi (159 kg/cm²)

Cured hardness                          82 Shore D

Dielectric strength                       400 Volts/mil

Application:

· Pipe repairs:

active pipe leaks

sealing joints

hazardous material spill control

reinforce thinning walls

· Repairs in hard to reach areas

· Underwater repairs

Directions for Use:

1. Minimize the flow rate and reduce system pressure

2. Roughen the area to be repaired

3. Knead the Seal Stic®

4. Place the Seal Stic® away from the leak location

5. Start wrapping the SealXpert® Ultra Sealing Tape a few distances away from the leak location

6. Continue to wrap SealXpert® Ultra Sealing Tape onto pipe while pushing the Seal Stic® onto leak location

7. Immerse Wrap Seal® Fiberglass Tape into water

8. Wrap the Wrap Seal® Fiberglass Tape above the repair tape as tightly and evenly as possible, using the entire roll

9. Discard the plastic tube at the end of the roll

10. Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap until all bubbling has stopped.

11. Repair completed with smooth and hard ivory appearance

Precision Underwater (Repair) Epoxy Putty Stick is a hand kneadable, two parts, co-extruded, fast curing epoxy putty, specially prepared to work in wet condition / underwater repair works / patching / sealing / bonds / rebuilding etc.

Underwater Epoxy Putty Stick is ideal for making emergency repairs in wet condition & underwater works. It’s cure rate is dependent upon the temperature of the water, just as it is affected by the air temperature in non-immersed applications. The lower the temperature the longer it takes to cure

Underwater Epoxy Putty Stick is hand mixable, speciality epoxy putty for repair of damp, wet areas & underwater surfaces. When mixed together, the material combine to from a polymer compound that may be applied underwater (Fresh water or salt water) and will bond tenaciously to substrates such as Fiberglass, Metal, Wood, Concrete, Ceramic, Glass, Plastic etc.

After full cure, it can be drilled, sanded or painter

(57 Grams Stick [2 Oz])
PRODUCT FEATURES:

Precision Underwater Epoxy Putty Stick / Wet Surface Repair Epoxy Putty Stick is a hand kneadable, two parts, co-extruded, fast curing epoxy putty, specially prepared to work in wet condition / underwater repair works / patching / sealing / bonds / rebuilding etc.

Underwater Epoxy Putty Stick is ideal for making emergency repairs in wet condition & underwater works. It’s cure rate is dependent upon the temperature of the water, just as it is affected by the air temperature in non-immersed applications. The lower the temperature the longer it takes to cure

Underwater Epoxy Putty Stick is hand mixable, speciality epoxy putty for repair of damp, wet areas & underwater surfaces. When mixed together, the material combine to from a polymer compound that may be applied underwater (Fresh water or salt water) and will bond tenaciously to substrates such as Fiberglass, Metal, Wood, Concrete, Ceramic, Glass, Plastic etc. After full cure, it can be drilled, sanded or painted.

PRECISION STEEL EPOXY PUTTY Stick (Co-extruded Composit Stick):
• Two part Steel filled Repair Epoxy Putty (Co-extruded Composit Stick).
• Ideal for repairing, Rebuilding of metal parts.
• Epoxy Putty has excellent machine-ability such as drilling, tapping, turning, milling, etc
• Can be Sanded & painted once fully cured.
APPLICATION: 
 
• Repair of Electrical Transformers
• strengthening of pipeline with fiber glass Reinforcement
• Filling eroded cavities
• Equipment disassembly
• Sealing of metal cracks / gaps
• Valves seat repairs.

PRECISION STEEL PUTTY is a steel reinforced, two part epoxy that cures to a metal-like finish and can be machined, drilled, tapped or filed.

Recommended Applications:

·       Sealing cracked castings, tanks, vessels and valves

·       Patching nonstructural defects of auto parts

·       Better choice compared to conventional Epoxy putty as this product prevents bimetallic corrosion

·       Making models and jigs for holding odd shaped parts

·       Making metal dies

·       Rebuilding worn out portions

·       Filling cavity areas

Advantages:

·       Does not sag or shrink – can be applied to overhead and vertical surfaces and

·       confirms to odd shapes

·       Rebuilds worn parts fast, reduces downtime

·       High steel content – cures to metal-like finish

·       Superior adhesion – forms a solid bond to clean and abraded steel, concrete, Bronze, Copper and Aluminum.

Direction of Use:

Surface Preparation

The surface should be free from oil, rust, dust, wax, grease, moisture. If surface is not cleaned, it affects the bonding of product to base substrate. Following methods of surface preparation are suggested.

·       Sand or shot blasting

·       Chipping out rust by scrappers, wire brush, emery paper

·       To remove oil & grease, use of cleaner/ conditioner is suggested. If sand blasting is not permitted, other mechanical means like wire brush, grinding, polish paper are required to be use

Introduction:

Quick Set Steel 5 Min Putty is a steel base, two part 100% epoxy system that cures in a very short time to a metal-like finish and can be machined, drilled, tapped.

Advantages:

* Does not sag or shrink - can be applied to overhead and vertical surfaces

* Fast leakage stopping reduces downtime

* High steel content - cures to a metal-like finish

* Superior adhesion - forms a solid bond to cleaned and abraded steel, concrete, Bronze, Copper.

* Reaches functional cure in few minutes.

Recommended Applications:

* Emergency repairs of leaking Pipes, Electric power Transformers, Tanks, other equipment

Direction of Use:

Proper surface preparation is important for the long term performance of the product.

The product performance and service life depends upon proper surface preparation and strict

adherence to instructions pertaining to application.

* Surface preparation should be done by roughening of the surface using portable grinder.

* Surface should be cleaned with cleaner so that it should be free from oil/ grease/rust and moisture.

Mixing:

* Resin and Hardener should be mixed thoroughly until a mixture of uniform colour is obtained.

* Be sure to mix along the sides and bottom.

Applications:

* Immediately after grit blasting / Grinding a thin layer of material should be rubbed onto the surface to wet for good adhesion (which acts like primer).

* Apply mixed material on the prepared surface by trowel or spatula. Ensure to consume the material (mixed) well before it becomes gel.

Precision Aluminium Epoxy Putty Stick is a hand knead able, two part, co-extruded, fast curing epoxy putty, specially prepared to work on diverse materials.
 
Aluminium Epoxy Putty Stick is ideal for making emergency repairs to reforming, rebuilding and patching anything made our of aluminium such as HVAC parts, Castings, Refrigeration units, Air conditioning units, machine parts, Aluminium Roofing and siding, Flagpoles, Shelving, platforms, Walkways, Campers, Road Vehicles, Canopies, Gutters, Truck and Trailer Bodies, Wheels Manifolds, Stripped Threads, Marine Hardware etc.
 
Colour- Aluminium grey (Resin part) / Beige (Hardener Part)
Packing - 4 Oz (114 Gms) sticks in transparent plastic container in display cartons of 12 No.
 
Physical Properties:
1) Work Life - 3-4 minutes (at 23 degree C)
2) Curing Time - 8-12 minutes (at 23 degree C)
3) Shelf life - 12 months
4) Hardness - Shore D-87
5) Safe working temperature - Continues- 120°C, Intermittent- 150°C.
6) Non-volatile contents - 100%
7) Tensile strength - 45 kg/Cm2.
8) Compression strength - 600 kg/cm2.
9) Excellent resistance to hydro carbons, moisture, saline weather and saline water, oil, minerals, solvents, mild acids, Alkalis, etc.

Precision Titanium Putty is a two part Epoxy based compound with thick paste like consistency. It is unique Epoxy putty which is useful for various metallic and non-metallic, diverse materials in workshops, industries, automobile service center, repair shops and construction Industry.
 
FEATURES BENEFITS:
 
 Two part Titanium & Steel filled Repair Epoxy Putty.
 Ideal for repairing, Rebuilding of metal parts.
 Epoxy Putty has excellent machine-ability such as drilling, tapping, turning, milling, etc.
 Can be Sanded painted once fully cured.

APPLICATION:
 Repair & rebuild of worn out Shafts, Bearing housings, Key ways,
 Repair of Electrical Transformers      
 Strengthening of pipeline with fibre glass Reinforcement
 Filling eroded cavities                        
 Equipment disassembly
 Sealing of metal cracks / gaps           
 Valves seat repairs
FOB Price: Rs.10,750
MOQ:1
Pack : 1 Kg

PRODUCT DESCRIPTION

Technology:

Epoxy Resin. 2 part solvent free epoxy compound. 

Product Features:

Precision Aluminium Putty, an all Purpose Aluminium metal filled Epoxy Putty.  

Precision Aluminium Putty is a high performance Aluminium metal filled Epoxy Putty, When Resin & Hardener mixed together, It reacts quickly to produce tough & rigid bond for long lasting repairs of Aluminium as well as all types of Ferrous & Non - Ferrous metals, various other multiple surfaces, repairs or rebuild critical equipment and quickly return it to service, minimizing expensive downtime and reducing cost. It forms a high strength, long lasting bond that can be grinded, sanded, drilled, machined & painted after curing.

Typical Properties:

APPLICATION AREAS 

Precision Aluminium Epoxy Putty can be applied on all types of Metals, Plastics, PVC, Glass, Fiberglass, Wood, China clay, Ceramic, Concrete, Stone & Many more.    

PRELIMINARY STATEMENT 

Before application it is suggested to read the Safety Data Sheet for information about precautionary measures and safety recommendations. 

PRE-TREATMENT 

The surfaces must be dry and free of oil, grease and dust.   

APPLICATION

It is recommended to use Precision Aluminium Putty in a well-ventilated area. To improve adhesion, roughen smooth surfaces. Then clean and dry all surfaces to be bonded.
Mix resin and hardener in the ratio as stated above, until the mixture is uniform.  After mixing is complete, Apply Aluminium Putty and give smooth surface with moist fingers.

Advantages:

·       Ultra Ceramic and silicon filed for protection against abrasion, cavitation & corrosion.

·       Easy to mix and use - ease of application reduces downtime.

·       Ultra-smooth brush able consistency - high gloss finish to fight friction, turbulence and protect against cavitation.

·       Superior adhesion.

·       Excellent performance in corrosion environment.

Recommended Applications:

·       Heat Exchangers & Condensers.

·       Water Boxes

·       Pumps & Impellers.

·       Pipes and Elbows

·       Tanks & Valves.